How does my automatic lawn sprinkler valve work?
Question by Michael G: How does my automatic lawn sprinkler valve work?
I have several “stations” in my automatic lawn sprinkler system. Each “station” has a valve that contains: 1. Manual Shutoff, 2. Flow Control Knob, 3. Solonid, & 4. Anti-Siphon valve. Any way my question is this, “Why does water continue to flow even when the manual shutoff is turned off and the flow control is also turned off?
Best answer:
Answer by John R
Any manual shutoff should shut the zone down completely, a flow control will limit the volume of water that leaves the valve by resticting the valve diaphram movement. If neither is working they may not be operational. A zone that continually runs either has a plunger stuck in the solenoid, a ruptured diaphram in the valve, or debris between the diaphram and valve body. If all these are contained in the valve, the most likely cause would be a bad diaphram or debris keeping the valve from closing completely
What do you think? Answer below!
Gilmour 996D Pattern Master Impulse Sprinkler
- Adjusts quickly – from 8 ft. to 59 ft. Water coverage up to 5800 sq. ft. (86 ft. X 59 ft.)
- Spray pattern adjusts to fit most square or rectangular shapes.
- The flexible spray tube bends up or down to set width of coverage.
- Flip action dial adjusts watering pattern from left to right for full, partial and in-between settings.
- Impact resistant, rustproof polymer construction.
No yard too odd for the Pattern Master Pulsating Sprinkler; once it’s programmed for a custom watering pattern, it repeats that pattern every time. The Pattern Master is a unique, adjustable sprinkler that waters virtually any shape lawn without wasting water on fences and driveways. This innovative impulse sprinkler waters up to 5,800 square feet and features a 43-foot watering radius. An easy-to-use programming disc adjusts up or down at sixteen positions within a single rotation-cutting the spray short to avoid the flower bed; going a little longer to soak that freshly planted tree; then launching a broad sweep across the far end of the yard so there’s no need to relocate the sprinkler down there later. With full rotation control, watering just about any obstacle course of a lawn is possible! The Pattern Master also features an adjust trip-lever and collars for full or partial coverage, a special speed control for even coverage, and a durable sled base for stability. Best of all, it
Rating: 
(out of 54 reviews)
List Price: $ 27.99
Price: $ 18.09
No pipes or plumbing connections needed for this buried, pop-up sprinkler system. Save $ thousands. Installed and running in minutes. Easy.
Related posts:
- Gilmour 196SPB Pattern Master Impulse Sprinkler on Polymer Sled Base Reviews
- Gilmour 996XL Large Coverage Pattern Master Impulse Sprinkler, Teal
- ifind2.com/Design – Automatic Lawn Sprinkler System Install
- How do I drive an AC solenoid like that found in a lawn sprinkler valve?
- Where can I get a moisture meter for my automatic lawn sprinkler system?
- Lawn Sprinkler System
- question about airating a lawn sprinkler system?
- Irrigation Lawn Sprinkler Systems
- Gilmour 999ZS Extra Large Coverage Sprinkler
- John Deere 4010J Traveling Sprinkler Green
the guy above me got to it before i did.
sounds like either a diaprham has just gone out, or the solenoid plunger is stuck, or there is a rock or something inside the valve, not closing it all the way. like trying to close a door with your foot in it. it will not close all the way.
A word of advice would be to go ahead and replace the anti-siphon valves with regular inline valves. anti-siphon valves are pretty much junk any type.
As far as diagnosing the problem now,
1. check your timer’s programming and make sure that its not sending out power to this zone all of the time. ( this would make the timer bad).
2. carefully open the valve up ( with the water turned off of course), and inspect the diaprham. if it has any tears or ripps in it, get a new diaphram, if not, then flush the lines out with the valve open to see if any debris is in the line( rocks pipe pieces, etc.) and clean it out.
3. take out the solenoid and make sure the plunger in it is not sticking. ( if so replace the solenoid).
4. if all else fails just simply cut out and replace the entire valve and plumb in a new one properly.
personally i would use either Hunter PGV valves, Rainbird DVF 100 valves, or Irritrol 205 series valves.
all are inline models.
antisiphon valves tend to fail. i work on sprinkler systems full time for 95 $ per hour of labor for our company.
hope this can help you out
John A